SF600 SPI NOR Flash Memory Programmer

285 €

SF600
Other than ICP Programming, it also supports socket adaptor programming.

Feature

The SF600 is a high speed "in System Programming" programmer to update the SPI Flash soldered on board (In-Circuit Programming) or in the socket adaptor (Offline programming). The programmer is easily controlled by the computer DediProg Software through the USB bus offering a friendly interface and powerful features to users.

SF600 combines the advantages of SF100 with additional improvements: High-speed USB and higher SPI performances.

Highlights

USB High speed and high SPI performance, support up to 2Gb SPI Flash
In circuit Programming: Program on-board SPI Flash
Offline Programming: Program SPI Flash in the socket
Program two Serial Flash memories
Start button feature: Able to Batch in the USB mode
Signal conflict protections
Multi-Programmers Capability through USB
Support 1.8V low voltage IC
Support Windows 2003 and above
Support both 32 and 64 bit OS
Support 1 CS pin

High performance (25MHz, Single IO):

USB Mode	Reference IC	Density	(Program + Verify)
Memory size	W25X80VSSIG	8Mb	9s
	W25Q16VSSIG	16Mb	11.6s
	W25Q32VSSIG	32Mb	12.6s
	W25Q64FVSSIG	64Mb	31s
	W25Q128BVFIG	128Mb	61.7s
	W25Q256FVFIG	256Mb	89.2s
	S25FL512SAGMFI011	512Mb	147.4s

*Please note the programming and verify time will depend on different IC type; please refer to the IC specification before programming.

Hardware

SF600 is designed with ISP header, through an appropriate connector, users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the SF600 2x10 header pin out. DediProg also provides the SF600 ISP Cable which is used to connect the SF600 programmer to the 2X6 2.54mm ISP Pin Header on board, please refer to Table 2 for the SF600 ISP Cable 2x6 pin out.

Table 1: SF600 ISP Header Pin Out (2x10)

1	Vpp	CS2	2
3	CS1	Vcc	4
5	MISO/DQ1	Hold/DQ3	6
7	Wp/DQ2	CLK	8
9	GND	MOSI/DQ0	10
11	NC	Reset/IO3	12
13	NC	NC	14
15	NC	NC	16
17	NC	NC	18
19	GPIO1	GPIO2	20

Table 2: ISP Cable Connector Pin Out (2x6)

1	Vpp	CS2	2
3	CS1	Vcc	4
5	MISO/DQ1	Hold/DQ3	6
7	Wp/DQ2	CLK	8
9	GND	MOSI/DQ0	10
11	NC	Reset	12

The SF600 USB software tool chain offers high flexibility and fits the different and highest requirements:

Engineering Graphic User Interface:

For engineers and expert to access advanced features for development, repairing etc.

Production Graphic User Interface:

For operators in production to control multiple programmers and improve the throughput.

Command Line Interface:

Customer software can control multiple SF600 programmers (SF600 integration, Control SF600 with Production In-Circuit Tester.)

Hardware Requirement for ISP :

To have a clear understanding on the different ISP or backup boot methods and different reference schematics, please download our dedicated application notes: AN0103 and AN0106

Standard Package

SF600 Programmer x 1
USB Cable x 1
ISP Cable (ISP-600-CB1-G) x 1
SF100 2.54mm 2*4 ISP Cable (ISP1-CB) x 1
SF600 Universal Adaptor (ADP-SF600-TO-SF100) x 1
CD-ROM (Included Software, specifications and user manual) x 1

Optional Purchase

Backup Boot Flash Module-8N
Backup Boot Flash Module-8W
Backup Boot Flash Module-D8W
Backup Boot Flash Module-DIP
Backup Boot Flash Module-16W
Backup Boot Flash Module QUAD-8W

SF600_ User_ Manual

Download (2.67M)

No reviews